Chrysler Town & Country Key Fob Battery Remote Replacement (1999 – 2016)
Your ultimate Chrysler Town and Country Key Fob Battery Replacement DIY
Key fobs promote easy access to your vehicle. No need for a manual key entry. You can unlock and lock your car automatically. What a convenience!
But what happens if the battery dies? Do you need to visit the dealer and pay a high price to get a Chrysler Town and Country Key Fob Battery Replacement? Absolutely not!
We’ve done all the hard work for you. In this blog, you will learn how to change the old battery in your key fob whenever it runs out of juice.
There are videos and there are written guides. Feel free to use the one you find most helpful or suitable to your learning style.
For other Chrysler models, see our Chrysler key fob battery page.
How to Replace the Chrysler Town and Country “Teardrop” Key Fob Battery (2008-2016)
Scroll down to watch a full video tutorial or keep reading for a step-by-step guide on Chrysler town and country key fob replacement.
What you will need:
1x CR2032 battery
First, check the bottom of the device. Can you notice the seam between the two halves of the key fob (where the key ring attaches)? Great. Now, push your flathead screwdriver into the corner of the seam, wiggling as you push. Once the tool is inside, twist it like a key. Repeat this until the two halves of the device pop open.
Next, carefully remove the rubber piece with the circuit board and set it aside. Now use your finger or screwdriver to gently lift the dead battery out of its compartment.
Take a new battery (CR2032) and slide it into place, let it click while ensuring the positive side faces down.
Finally, set the rubber buttons back on top and click the front piece of the plastic cover back into place. Ensure the cover clicks securely.
You’re done! You just changed your key fob battery at home.
Test your new remote key battery: unlock and lock your car doors. Did that work fine? Awesome. Now sit back and enjoy your keyless entry remote.
This is the battery for this Chrysler Town & Country “Teardrop” key fob:
How to Replace the Chrysler Town & Country “Fixed Key” Key Fob Battery (2004, 2005, 2006, 2007)
Scroll down to watch a full video tutorial or keep reading for a step-by-step procedure on Chrysler key fob battery replacement.The tools you will need:
1x CR2032 battery
First thing, look for a small indentation on the bottom-left side of the key fob (right beside the metal key. Once you locate that, insert a small flathead screwdriver into this slot and turn it like a key. This action will separate the two halves of the key fob.
Next, carefully remove the rubber piece with the circuit board inside. Set it aside. This will grant you access to the old battery to be replaced.
Now that you are inside, use your screwdriver to carefully remove the old battery. This one’s pretty easy. All you have to do is get your tool under the battery and gently lift it up. The battery will pop right out.
Take a new battery and install it into place making certain that the positive side of the battery is facing the positive side of the battery clip.
Finally, return the rubber piece to its place and click the face of the key fob back on.
Nice job! You’ve successfully replaced your keyless entry remote. Remember to lock or unlock your vehicle door to test its functionality.
This is the battery for this Chrysler Town & Country “Fixed Key” key fob:
How to Replace the Chrysler Town & Country “Pear-Shaped” Key Fob Battery (1999, 2000, 2001, 2002, 2003)
Scroll down to watch a full video tutorial or keep reading for a step-by-step procedure on your Chrysler town and country key fob battery replacement.
What you will need:
2x CR2016 batteries
Start by locating the little slot on the bottom right side of the key fob. Found it? Good.
Now, insert a flathead screwdriver into the slot and twist until you are able to pry apart the two halves of the device. You should be staring right at the first battery on top now. The second one is underneath the first.
Next, use your fingernail or screwdriver to remove both of the batteries. To do this,
Install and click the two new CR2016 batteries into place, one on top of the other, both positive sides facing up. Note that if you replaced the battery the wrong way, your keyless entry remote wouldn’t work.
Lastly, all you need to do now is click the two halves of the key fob back together. If you removed a metal key from the key fob, remember to return it.
Congrats! Your brand-new key fob batteries should be working properly now. That keyless entry remote is still possible after all.
This is the battery for this Chrysler Town & Country “Pear-Shaped” key fob:
What kind of battery does a Chrysler key fob take?
You will often find an Energizer CR2032 3v battery in most Chrysler models. Should there be a need for replacement, this is the battery that will replace the original one for a keyless entry remote.
How long does a key fob battery last?
Most key fob batteries last as long as 3 to 4years. However, their lifespan depends on how often you use them and the environmental conditions. You can also refer to the manual for your battery type. lifespan
Replacing a dead battery in keys is easy with the right guide. And that’s what you will find above. Don’t wait till you’re stuck in the middle of nowhere because your key fob battery suddenly stops working. Learn the right Chrysler Town and Country key fob battery replacement DIY now. Whichever models you use, be it Chrysler grand voyager, lancia grand voyager, or other ones, you use our guide for them
If you found this post helpful or have any questions, feel free to let me know in the comment section below and I will get right back to you. If you need more information you can also check the rest of our YouTube videos on our channel or click on fobbattery.com. Good luck!